Switches and Wires

Special Order item allow 3-4 weeks for delivery

SmoothFlite 16

Welcome to the world’s first Automatic Intelligent Servo Matching System (ISMS)

Intellimatch is the result of 2 years of research and development, is designed to take the worry out of servo matching and gives you the maximum power, smoothest response and increased life from your servos.

If you have built giant scale models before with multi servo control surfaces then I am sure you will be familiar with the process of manually matching the servos. You generally match servos on 2 end points and maybe a center point. That’s a total of only 3 matching points. There is no way 3 points will accurately match your servos. Also, you have to adjust each servo until minimal buzz is heard or you might use an ammeter to minimize current draw. Throw that idea away...

With the Booma RC Intellimatch you say goodbye to traditional methods of servo matching. The Intellimatch system automatically matches servos on 100 points through the servo sweep range. That is 100 points not just the traditional 2 or 3. Intellimatch further adds smoother operation by reading the closest 2 points from the servos current position and then interpolates between the 2 selected points to a resolution of 8192 steps. 8192 step resolution is the highest resolution available today.

The IM14 Intellimatch unit is designed to match 1 set of up to 4 servos. An example IM14 usage might be up to 4 rudder or ailerons servos

Read on for the full list of features

Model Example 1 - 100cc Scale Aero Model:

-2 Aileron Servos per aileron

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories

-2 x IM22 = 1 x IM22 for Ailerons and 1 x IM22 for Elevators

Model Example 2 - 150cc Scale Aero Model:

-3 Aileron Servos per aileron

-2 Elevator Servo per elevator

-3 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = 1 x IM22 for Elevators

-2 x IM14 = for Ailerons

-1 x IM14 = for Rudder

Model Example 3 - Large Jet:

-2 Aileron Servos per aileron

-2 Flap Servos

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = for right side Ailerons and Flaps

-1 x IM22 = for left side Ailerons and Flaps

-1 x IM22 = for Rudder

Specs:

• 32 bit Processor for the highest speed and resolution in the industry

• Automatic matching of up to 4 servos on a single channel

• 100 matched point across the servo sweep range

• 82 step real time interpolation between the 100 matched points

• PWM resolution of up to 8200 steps

• Dual LED indication for programming feedback

• Recommended battery chemistry - Life (2 cells), LiPo (2 cells), Lion (2 cells), NiCd(5cells),Nimh(5 cells)

• Maximum input voltage 10 volts

• Minimum input voltage 5 volts

• Compatible with all receivers and Power Distribution systems

• Works with Advanced Radio AR1232 and AR824. Also compatible with all other receiver and Power Distribution systems

• Dual fail safe arming with the supplied arming plug

• On board Flash storage - 100 year data retention

• Weight is only 12 grams

• Dimensions 49mm x 23mm (3.5 x 2.5 inches)

Description:
10 pack of servo safety clips. Made to retain your servo wires to keep them from slipping off during flight.

A must have to to ensure your servo connectors stay securely connected.

Packs of 10:

Extreme RRS--16 CH High Power Expander

Welcome to the world’s first Automatic Intelligent Servo Matching System (ISMS)

Intellimatch is the result of 2 years of research and development, is designed to take the worry out of servo matching and gives you the maximum power, smoothest response and increased life from your servos.

If you have built giant scale models before with multi servo control surfaces then I am sure you will be familiar with the process of manually matching the servos. You generally match servos on 2 end points and maybe a center point. That’s a total of only 3 matching points. There is no way 3 points will accurately match your servos. Also, you have to adjust each servo until minimal buzz is heard or you might use an ammeter to minimize current draw. Throw that idea away...

With the Booma RC Intellimatch you say goodbye to traditional methods of servo matching. The Intellimatch system automatically matches servos on 100 points through the servo sweep range. That is 100 points not just the traditional 2 or 3. Intellimatch further adds smoother operation by reading the closest 2 points from the servos current position and then interpolates between the 2 selected points to a resolution of 8192 steps. 8192 step resolution is the highest resolution available today.

The IM14 Intellimatch unit is designed to match 1 set of up to 4 servos. An example IM14 usage might be up to 4 rudder or ailerons servos

Read on for the full list of features

Model Example 1 - 100cc Scale Aero Model:

-2 Aileron Servos per aileron

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories

-2 x IM22 = 1 x IM22 for Ailerons and 1 x IM22 for Elevators

Model Example 2 - 150cc Scale Aero Model:

-3 Aileron Servos per aileron

-2 Elevator Servo per elevator

-3 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = 1 x IM22 for Elevators

-2 x IM14 = for Ailerons

-1 x IM14 = for Rudder

Model Example 3 - Large Jet:

-2 Aileron Servos per aileron

-2 Flap Servos

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = for right side Ailerons and Flaps

-1 x IM22 = for left side Ailerons and Flaps

-1 x IM22 = for Rudder

Specs:

• 32 bit Processor for the highest speed and resolution in the industry

• Automatic matching of up to 4 servos on a single channel

• 100 matched point across the servo sweep range

• 82 step real time interpolation between the 100 matched points

• PWM resolution of up to 8200 steps

• Dual LED indication for programming feedback

• Recommended battery chemistry - Life (2 cells), LiPo (2 cells), Lion (2 cells), NiCd(5cells),Nimh(5 cells)

• Maximum input voltage 10 volts

• Minimum input voltage 5 volts

• Compatible with all receivers and Power Distribution systems

• Works with Advanced Radio AR1232 and AR824. Also compatible with all other receiver and Power Distribution systems

• Dual fail safe arming with the supplied arming plug

• On board Flash storage - 100 year data retention

• Weight is only 12 grams

• Dimensions 49mm x 23mm (3.5 x 2.5 inches)

Hobbywing 3A Power Regulator 5/6V UBEC (2-6S Input)

Description:

GT Power Servo Consistency Master.

With this cool device you can test up to 3 servos at a time for consistency and precision. With the GT Power servo tester you can see how servos react in three different testing modes. Manual, Neutral, and Automatic.

---

Manual Mode:: Turn the knob at different speeds however you want to check reaction time.

Neutral Mode:: Make the servo go back to the neutral position.

Automatic Mode:: "window wiper mode"- make the servo swing back and fourth at max angle.

---

Specs:

• Connect 1-3 servos simultaneously
• Test in 3 different modes
• Easy to read labels
• LED lights

24" Charge / Balance Lead Extension Kit

8-Function Charge Adapter to Male 4mm Bullets-300mm Wire 

Racer's Edge provides an ideal solution for enthusiasts with multiple models using batteries with various connectors. This convenient charging squid comes equipped with virtually every possible connector that a modeler may require. Plugs included: Tamiya, Deans, TRX, XT60, JST, EC3, universal receiver pack, and if we've forgotten anything there is a pre-tinned pair of wires awaiting installation of your favorite connector. 

XT60 Series Connector XT60 Female to 2 XT60 Male Adapter

Description:
Male Deans to Male XT60 Connector

With this Deans to XT connector you can convert a battery with T-Plug to XT-60 on ESC / charger
The connector has many applications and can be used for charger adapter.

Features:

• Male Deans T style plug to Female XT60 (adapter for XT60 power Boards to convert to Deans)
• Durable design
• Heatshrink seal

QS8-S Heavy Duty Anti Spark Connector (1 pair M/F 130A) 

Description:
Male Deans to Male XT60 Connector

With this Deans to XT connector you can convert a battery with T-Plug to XT-60 on ESC / charger
The connector has many applications and can be used for charger adapter.

Features:

• Male Deans T style plug to Female XT60 (adapter for XT60 power Boards to convert to Deans)
• Durable design
• Heatshrink seal

Description:
5 Pairs of Deans Style Connectors

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.
 

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR

XT60 Connectors

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR

XT90 Connectors

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR

XT90 Anti-Spark Connectors 

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR

EC3 Connectors 

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR