General Accessories

12oz Smoke Tank
[email protected]

Take the guesswork and worry out of properly setting up your aircrafts smoke system with these ready to use 4titude smoke tanks. Just strap it in and fly!

We've been receiving a few requests for the smoke tanks and as usual Redwing RC has LISTENED! Introducing the Fourtitude Smoke Tanks available now at Redwing RC! You're welcome :-)

 

Features:

• Crystal Clear allowing quick visual checks of any possible pollutants in your smoke tank.
• Lightest weight commercially available R/C smoke tank on the market. Many cases less than half the weight of the older roto molded “standard” tanks.
• Aerospace Mil spec sealant used in assembly to assure the tank will hold up to many high G loaded flights!
• Incredibly resilient and truly seamless tank body with a threaded on closure
• No rubber stopper to crack, leak, or split your tank apart.
• Detailed installation instructions.
  
  Fourtitude R/C RTU Smoke tanks include: A high quality double sided hook and loop mounting strap, precut to shape foam mounting pad, and Fourtitude R/C blue fuel line to plumb your aircraft. Everything you need to get smoking up the sky ASAP!
  
  These crystal clear plastic tanks are square shaped which makes mounting into your aircraft very simple. Every tank is QC pressure leak tested.

  12oz Fourtitude SMOKE Tank

  
   

32oz Smoke Tank


Take the guesswork and worry out of properly setting up your aircrafts smoke system with these ready to use 4titude smoke tanks. Just strap it in and fly!

We've been receiving a few requests for the smoke tanks and as usual Redwing RC has LISTENED! Introducing the Fourtitude Smoke Tanks available now at Redwing RC! You're welcome :-)

 

Features:

• Crystal Clear allowing quick visual checks of any possible pollutants in your smoke tank.
• Lightest weight commercially available R/C smoke tank on the market. Many cases less than half the weight of the older roto molded “standard” tanks.
• Aerospace Mil spec sealant used in assembly to assure the tank will hold up to many high G loaded flights!
• Incredibly resilient and truly seamless tank body with a threaded on closure
• No rubber stopper to crack, leak, or split your tank apart.
• Detailed installation instructions.
  
  Fourtitude R/C RTU Smoke tanks include: A high quality double sided hook and loop mounting strap, precut to shape foam mounting pad, and Fourtitude R/C blue fuel line to plumb your aircraft. Everything you need to get smoking up the sky ASAP!
  
  These crystal clear plastic tanks are square shaped which makes mounting into your aircraft very simple. Every tank is QC pressure leak tested.

  32oz Fourtitude SMOKE Tank

  
   

The New RedwingRC T-shirt

Show your Redwing pride at the field and add to your Redwing swag collection!

100% cotton

Available in S, M, L, XL, 2XL, 3XL

Description:

Crimper

Use this heavy duty crimper to crimp pin/socket onto your wires. Easy to use and comes with step by step instructions.

Also works as a wire cutter. (see image)

Rcexl Walbro Style Weighted Felt Fuel Clunk

Fuel clunks are a must for aerobatic flying. It insures that fuel is always flowing to the engine because the fuel line will follow gravity inside your tank. Without one, you increase the chance that your plane may stall when flying inverted or performing different maneuvers. Installing a fuel clunk is simple to install and an investment that any serious pilot should make.

13x16mm

.4 oz

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

• Balsa Wood
• Ceramics

Works Good On:

• Soft Wood
• Fiberglass
• Hard Plastics
• Water-Resistant
• CA Hinges

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure+™ Super Glue, CA

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning

Works Best On:

• Balsa Wood
• Soft Wood

Works Good On:

• Hard Wood
• Glass & Metals
• Fiberglass
• Ceramics
• Hard Plastics
• Rubber
• Laminating
• Water-Resistant
• Reinforcing

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet

Untitled Document

Description:

Bob Smith Industries CA Glue

Maxi-Cure™ Super Glue, CA

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Works Best On:

• Soft Wood
• Hard Wood
• Glass & Metal
• Fiberglass
• Ceramics
• Hard Plastics
• Rubber
• Laminating
• Reinforcing

Works Good On:

• Balsa Wood
• Water-Resistant

Click to Download Safety Data Sheet

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

Works Best On:

• Rubber
• White Foam

Works Good On:

• Balsa Wood
• Soft Wood
• Hard Wood
• Glass & Metal
• Fiberglass
• Ceramics
• Hard Plastics
• Laminating
• Water-Resistant
• Reinforcing
• CA Hinges

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet

Description:

This tail wheel assembly is extremely efficient and reliable. With fewer parts, there is less to worry about and the solid construction makes it the go-to choice for pilots at any skill level. The new V2 design incorporates ball bearings for smooth motion, ball-joint to rudder steering connection, wider CF mounting plate, and slightly larger wheels that the v1. "Trouble Free" means just that... no more worrying about screws falling out or loss of control. Make the switch today by installing the SmartDesign Tail Wheel!!!

CNC Aluminum & C.F. Tail Wheel Assembly for 20cc to 220cc

Features:

• Extremely Reliable
• Mechanically Efficient Design
• Simple and Solid Construction
• Fewer parts needed for install
• Ball Bearings

Pricing

• 20-40cc: $27.00
• 50-70cc: $34.99
• 85-120cc: $44.99
• 150cc-220cc: $54.00

Weight

• 20-40cc: 1.2 oz
• 50-70cc: 1.6 oz
• 85-120cc: 2.2 oz
• 150cc-220cc: 2.6 oz

Don't forget to check out our Aluminum Hub Wheels! They are excellent replacements for landing gears and tail wheels. Please see sizing chart below.

Description:

These Aluminum Hub Wheels are made with High Quality Rubber tires that will make landing softly a breeze. Designed to fit 20cc to 170cc

Wheels are sold in pairs.

Features:

• Reusable Aluminum Hub
• High Quality Rubber Tire

Pricing

• 3"- 20-30cc: $15.99
• 3.5"- 50-60cc: $18.99
• 4"- 100-120cc: $20.51
• 4.5"- 150-170cc: $25.00

Weight (for two wheels)

• 20-30cc: 2.6 oz
• 50-60cc: 2.8 oz
• 100-120cc:6 oz
• 150-170cc: 7 oz

Untitled Document

Description:

Bob Smith Industries Foam Cure

Foam-Cure™

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.

FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

Works Best On:

• EPP Foam
• EOP Foam
• Clear Canopy
• Paper and Crafts

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.

Click to Download Safety Data Sheet