Miracle Accessories

 

 

Description:
Miracle Switches use heavy duty 22AWG silicone wire. Switches can be used for dual redundant receiver battery packs or for one receiver battery pack and one ignition battery pack. 3 options available



Specifications:

 

 

• Dual Switch - 1.5oz
• Dual Switch and Fuel Dot - 1.8oz
• Single Switch and Fuel Dot - 1oz.

Description:
These Miracle fuel dots are GREAT looking and function just as well. They are made of machined aluminum, and have a neoprene O-ring for a tight fuel proof fit. They include all the hardware you need and work with all standard size tygon tubing.

Description:
This Drill Jig is a high quality heavy steel jig that can be used to perfectly drill your props and spinners for the DLE 30cc, DLE 35RA, DLE55, DLE55RA, DA, DL, DLA, 50cc, MLD 28cc, and EVO 54cc

Simply slide the prop or spinner onto the guide and tighten down the bolt to secure it and drill out the holes using the included drill bits!

Description:

All NEW design! These Miracle aluminum spinners have back plates which have extensive lightening, the spinners are cut for a large 3d style prop, and the back plates are drilled for multiple engine sizes!

FOR ENGINE SIZE:

• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 3" Spinner: DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
• 3.5" DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
  
  SPECS:
• 2.5": Height 2.7", weight 2.7oz, includes 30mm bolt.
• 3": Height - 3.1", weight 3.2 oz, includes 55mm bolt.
• 3.5" : Height 3.7", weight 3.6oz, includes 60mm bolt.

 

 

Miracle RC Aluminum Spinners are high quality CNC Machined spinners. Very light, with a lightened back plate included. Very accurate, very beautiful, and a great value!

 

• 2.5" - $16.95
• 3" - $20.95
• 3.5" - $27.95
• 3.75"- $31.95
• 4.0" - $38.95
• 4.5" - $44.95
• 5" - $50.95

Description:
Make SURE your control surfaces are moving in even amounts in ALL directions.

Quality you can count on
This high quality CNC anodized throw meter, is made to precisely measure your surface deflections. Just clip on the aileron or elevtor (with it's padded light grab clip) and then turn the dial to show zero. Move your surface up or down and record your degree of throw. Match it with your other side, AND the other direction easily, quickly and PRECISELY!

Description:
This Miracle RC Fuel pump is a MUST have accessory. Saves you time and elbow grease when filling up your tank. The case is CNC process 6061, and it has a hardened pump barrel. It has a magnet on the outside, so you it can stick right onto metal containers!

The gears are fuel proof nylon, and fiberglass filled
The gear shaft is stainless steel
Japaneese oil seals
The end-seal O-ring is made of butadience-acrylonitrile rubber - so it can be used with nitro, gas, or even kerosene
volatage: 7.2 to 12V
Flow rate: 1000ml/min at 11.1V
Includes a filtered nozzle and clunk

DO NOT DRY RUN

Description:

With the Miracle RC prop reamer you can increase the diameter of the hole in your prop while keeping it true and square.

The Miracle prop reamer cuts in increments of 5mm, 1/4", 5/16", 3/8"

The Miracle prop reamer is made of a harder steel than most to stay strong for MANY cuts for many years.

 

Miracle RC Belly stand for your Radio

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch
 

Description:
The Miracle RC, CDI Shock Stand is made to prevent damage to your CDI/Ignition system, by abosorbing harmful vibrations caused by your engine. The Miracle RC CDI Shock Stand can also help to prevent damage from crashes or hard landings. The Shock Stand is made of light weight high quality annodized aluminum. Included with the Miracle Shock Stand are all the accessories you will need to properly mount your ignition and stand, such as a velcro strap, spare hook and loop, screws, washers etc.



Specifications:

• Weight:
• Dimensions appx: 90mm x 57mm

 

 

Includes:

 

 

• Stand
• Velcro Strap
• Mounting Washers
• Self adhesive velcro
• screws

 

 

 

Miracle long fuel filling nozzle with fuel filter.
Available in Red, Gold, and Blue.
Please make a note of your color choice.

Description:

Looking for a precise and easy way to balance your props and spinners? Redwing RC has what you need. The Miracle Precision Balancer is made of quality CNC aluminum parts and are used to ensure precise balance of your RC components - making sure they operate quietly and accurately - ultimately giving your props and spinners a longer life!