Miracle Accessories

New Miracle Brushless Smoke Pump 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Introducing the Red Miracle Brushless Motor Smoke Pump! These light weight pumps have a CNC processed 6061 case with a Japanese high speed oil seal. The brushless motor/ESC supply smooth transmission and helps avoid the possibility of a spark.

Basic Set up:

First connect the pump to the ESC, fuel filters, muffler and smoke tank (drawing included to help with this).Plug your radio connector into the switched channel (such as landing gear or flaps). Turn on radio, make sure switch is off (100% negative) for at least 5 seconds and turn on. If the pump pushes fluid toward the muffler, the set up is correct. If it tries to pump toward the tank, please change any two wires' connection of the three wires connect the brushless motor and ESC.

Radio Set up:

3. Non programmable Radios

Use a switched channel to switch the Smoke pump on and off. Since there is no trim control on a switched channel, the flow rate is consistent. When the switch is on, flow will be at maximum. We can set the END POINT/ATV of radio switch channel to control the maximum flow rate so as to control the smoke density.

4. Programmable Radios

Plug the smoke signal wire into a spare channel (such as the 8th channel). Set this channel program mixing the Throttle channel, then set a switch for programming mixing on/off to control smoke pump on/off. Adjust the END POINT/Travel of this channel to control smoke pump flow rate so as to control the smoke density. For more detailed information please see your radio manual.

 

 

Specifications:

 

 

• Weight: 3.32 oz (94g)
• 1100KV Brushless Motor
• 10 Amp Brushless ESC
• Input: 2-cell lipo or Li-FE (6-cell NiMH)
• CNC processed 6061 anodized aluminum
• Fuel resistant fiberglass filled nylon gears
   

  **DO NOT dry run pump! This may cause failure and will void warranty.**

   

Miracle Fuel Dot Stopper/Fuel Filler Nozzle for RC Fuel Line Systems

Material: Aluminum with Rubber O-Ring

Dimensions: See Picture (2 per pack)

Specify color.

Miracle 1.75" (44.5mm) Drilled Aluminum Bullet Spinner for DLE30/55 MLD35/70 DA50 EVO54 Engine

All NEW design! These Miracle aluminum spinners have back plates which have extensive lightening, the spinners are cut for a large 3d style prop, and the back plates are drilled for multiple engine sizes!

FOR ENGINE SIZE:

• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 3" Spinner: DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
• 3.5" DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
  
  SPECS:
• 2.5": Height 2.7", weight 2.7oz, includes 30mm bolt.
• 3": Height - 3.1", weight 3.2 oz, includes 55mm bolt.
• 3.5" : Height 3.7", weight 3.6oz, includes 60mm bolt.

 

 

Miracle RC Aluminum Spinners are high quality CNC Machined spinners. Very light, with a lightened back plate included. Very accurate, very beautiful, and a great value!

 

 

• 2.5" - $16.95
• 3" - $20.95
• 3.5" - $27.95
• 4.5" - $44.95
• 5" - $50.95

Miracle Dual/Twin Fuel Dot for Fuel and Smoke

Miracle CNC Transmitter Stand Support

Miracle CNC Adjustable Servo Mount

Miracle CNC Single Rudder Tray with Anodized Rudder Arm KIT

Miracle CNC Dual Rudder Tray with Anodized Rudder Arm KIT

Miracle CNC Triple Rudder Tray with Anodized Rudder Arm KIT

Description:
10 pack of servo safety clips. Made to retain your servo wires to keep them from slipping off during flight.

A must have to to ensure your servo connectors stay securely connected.

Packs of 10:

Miracle CNC 2.5" Straight Heavy Duty Double Full Servo Arm (Futaba/Hitec/JR)

Miracle CNC 3.5" Straight Heavy Duty Double Full Servo Arm (Futaba/Hitec/JR)