Bob Smith Industries Foam-Cure
Untitled Document Description:Bob Smith Industries Foam Cure Foam-Cure™FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.
Works Best On:
Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.
Click to Download Safety Data Sheet
|
Miracle CNC Heavy Duty Half Servo Arm 1.25-1.5" and 1.75-2" (Futaba/Hitec/JR)
| Miracle CNC Heavy Duty Half Servo Arm 1.25-1.5" and 1.75-2" (Futaba/Hitec/JR) |
MRC-F-024-Servo-Arm
$12.99
BMS-127+ MICRO WIDE VOLTAGE-DIGITAL, HIGH SPEED, CORELESS SERVO (5.3kg/73.7oz 0.05sec 8.4V)
BMS-127+ MICRO WIDE VOLTAGE-DIGITAL, HIGH TORQUE, CORELESS SERVO (5.3kg/73.7oz 0.05sec 8.4V) |
BBR-BMS-127WV+
$23.99
Power HD B4S Brushless Servo - 32kg/cm (444.4 oz/in), 0.065sec 8.4V - (Super High Speed and SR/SXR/SSR/SUR/SFR Compatible)
Power HD B4S Brushless Servo - 32kg/cm (444.4 oz/in), 0.065sec 8.4V - (Super High Speed and SR/SXR/SSR/SUR/SFR Compatible)Check out the new Power HD 0804HV Brushless servos! These are great to use a throttle servo and can be used in systems with other high voltage servos! The Power HD 0804HV high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life. "What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD 0804HV high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you. These servos are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced. All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting. So now the only question is - why are you still reading this? Go buy your Power HD 0804HV servos before they're gone!
Specs:
|
HD-B4S
$75.99
