TAFT-HOBBY QUANTUM 90MM EDF JET 6S PNP VERSION

Description:

Pulse Lithium Polymer Batteries - Setting a New Standard.

As Lithium Polymer battery technology continues to push new boundaries, Pulse Lithium Polymer Batteries bring a whole new element into the mix - power & performance at a price that simply can't be ignored. 

Designed specifically for the demands of the latest power plants, not to mention the new realm of extreme 3D flight, Pulse brings a whole new battery to bear at a cost never seen before. Simply put, premium power no longer comes at a premium price.

Incorporating the latest advancements in Lithium Polymer technology, Pulse Batteries are designed to bring performance levels to a new stratosphere with 35C, 45C, and 65C battery packs in multiple capacities for the helicopter of your choice. Add the 5C charge rates, and the fun just begins. 

Pulse Lithium Polymer Batteries - Can You Feel Your Pulse Quicken?

Pulse Batteries Available Individually or in a PRE-MADE System!

Take the guesswork out of your electric battery set up- we've done it for you! Check out the suggested set up systems for 30cc and 50cc.

LiPo 4500mah 5S, 18.5v - $104.99 each

30cc 10S System: Two (2) LiPo 4500mah 5S, 18.5v - $208

• Voltage: 18.5V
• Cell Count: 5S
• Capacity: 4500mAh
• Discharge Rate: 45C
• Dimensions: 159mm x 45mm x 38mm (LxWxH)
• Weight: 630g
• Balance Tap: JST-XH

LiPo 3300mah 45C 6S, 22.2v - $94.99 each

30cc 12S System #1: Two (2) LiPo 3300mah 45C 6S, 22.2v - $188

• Voltage: 22.2V
• Cell Count: 6S
• Capacity: 3300mah
• Discharge Rate: 45C
• Charge Rate: 5C
• Dimensions: 139mm x 42mm x 43mm  (LxWxH)
• Weight: 567g
• Balance Tap: JST-XH

LiPo 3700mah 45C 6S, 22.2v - $109.99 each

30cc 12S System #2: Two (2) LiPo 3700mah 45C 6S, 22.2v - $218

• Voltage: 22.2V
• Cell Count: 6S
• Capacity: 3700mAh
• Discharge Rate: 45C
• Charge Rate: 5C
• Dimensions: 138mm x 44.5mm x 48mm (LxWxH)
• Weight: 567g
• Balance Tap: JST-XH

LiPo 4100mah 45C 6S, 22.2v - $119.99 each

30cc 12S System #3: Two (2) LiPo 4100mah 45C 6S, 22.2v - $238

• Voltage: 22.2V
• Cell Count: 6S
• Capacity: 4100mAh
• Discharge Rate: 45C
• Charge Rate: 5C
• Dimensions: 137mm x 53mm x 42mm (LxWxH)
• Weight: 680 grams
• Balance Tap: JST-XH

LiPo 5000mah 45C 6S, 22.2v - $139.99 each

50cc 12S System #1: Two (2) LiPo 5000mah 45C 6S, 22.2v - $278

• Voltage: 22.2V
• Cell Count: 6S
• Capacity: 5000mah
• Discharge Rate: 45C
• Charge Rate: 5C
• Dimensions: 158mm x 45mm x 49mm  (LxWxH)
• Weight: 800g
• Balance Tap: JST-XH

LiPo 5500mah 45C 6S, 22.2v - $149.95 each

50cc 12S System #2: Two (2) LiPo 5500mah 45C 6S, 22.2v - $298

• Voltage: 22.2V
• Cell Count: 6S
• Capacity: 5500mah
• Discharge Rate: 45C
• Charge Rate: 5C
• Dimensions: 160mm x 44.5mm x 52mm  (LxWxH)
• Weight: 873g
• Balance Tap: JST-XH

LiPo 6000mah 35C 6S, 22.2v - $149.99 each

50cc 12S System #3: Two (2) LiPo 6000mah 35C 6S, 22.2v - $298

• Cell Count: 6S 22.2V
• Capacity: 6000mah
• Discharge Rate: 35C
• Charge Rate: 5C 
• Dimensions: 160mm x 49mm x 51mm  (LxWxH)
• Weight: 884g
• Balance Tap: JST-XH

Purchase pre-made system or buy individually! Select below.

6S 5200MAH 75C LIPO BATTERY

Description:

Do you want a more SCALE engine purr?! Look no further, these DLE Muffler Silencers will give that throaty sound to your engine with very little muss or fuss. This DLE Muffler Silencer significantly reduces the high pitched noise of the DLE 30 and makes it sound more scale - and they hardly increase the temperature of your cylinder head.

This unit ONLY works on the DLE 30.

Simply press fit the silencer in place and then hold with the included silicone tubing and zip ties - or drill a hole and install a screw - either way installation is easy - and these bad boys don't go anywhere! Friction alone helps keep them in place.

This silencer is a simple way to reduce the noise level of your rc engine without compromising the quality or performance - and at OUR price?! Simply cannot be beat.

Sold Individually! RA's or others with 2 exhaust pipes will need 2

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

• Balsa Wood
• Ceramics

Works Good On:

• Soft Wood
• Fiberglass
• Hard Plastics
• Water-Resistant
• CA Hinges

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet

Taft-Hobby Turbo Bushmaster STOL 72"(1.8M) Wingspan - PNP 6CH with Flaps and LED Lights (Night Flyer)

$20 Flat Rate shipping lower 48 USA only. Contact us at [email protected] to calculate international shipping cost.

RedwingRC Plug-and-Play aircraft!

The Dynam T28 Trojan is a great plane for both beginners and experienced pilots! Just getting started in the hobby or just want to try something new, this plane is for you. The Trojan T28 is made with EPOFLEX (EPO) foam- a damage resistant foam. This aircraft is painted with the famous US Air force color scheme. All surfaces are constructed out of the EPO foam so it is not easily damaged and easily repaired. The Trojan is very stable and is a blast to fly! This is a Plug-and-Play aircraft so it will arrive about 80% complete and included cool scale features such as a clear canopy, retractable landing gears and steerable nose landing-gear .

Build time is around 60 min from box to air.

Expect flight time to be from 6-10 minutes per battery.

Key Features:

• Powerful BM3715 - 890KV outrunner brushless power system
• 30A Brushless ESC
• Retractable landing gears
• Durable and lightweight EPO construction with many surface details
• Detailed Body Structure
• Suitable for both, beginner thru experienced Pilots
• Easy to build
• Scale 3 blade prop

Specifications: