Beechcraft T-34 Mini 470mm Laser-Cut Balsa Wood Model Kit (Kit, PNP or BNF Electric Power version)
Beechcraft T-34 Mini 470mm Laser-Cut Balsa Wood Model Kit (Kit, PNP or BNF Electric Power version) The Beechcraft T-34 Mentor is an American propeller-driven, single-engined, military trainer aircraft derived from the Beechcraft Model 35 Bonanza.The earlier versions of the T-34, dating from around the late 1940s to the 1950s, were piston-engined. The T-34 was the brainchild of Walter Beech, who developed it as the Beechcraft Model 45 private venture at a time when there was no defense budget for a new trainer model. Beech hoped to sell it as an economical alternative to the North American T-6/SNJ Texan, then in use by all services of the U.S. military.. Our model captures the very essence of this early fighter aircraft. This Micro Balsa plane is built from balsa and hardwoods with all the parts beautifully laser cut that are extremely accurate allowing you to build the perfect model. This kit is easy to operate and suitable for beginners and the PNP comes with everything you need except your battery and RX/TX. BNF includes 2 batteries and charger plus DSMX Receiver! Features:
Specifications:
Optional Power System:
Kit Versions: K1301= KIT only K1302= KIT+Motor(1104 3700KV+1.5mm Prop Saver+5030 Prop+2.0 Pin 3P) K1304 (PNP)= KIT+Motor+ESC( 1S7A+2.0Pin 3P+Walkera Female 2P+1.25P 2pin)+Servo(1.7g*2) K1305 (PNP+)= K1304+2pcs*1S 100mAh Battery+USB Charger K1305-144 (BNF)= K1305+Mini Receiver RX144 (DSMX/2) Free shipping lower 48 USA only. Contact us at [email protected] for international shipping |
Dynam 11x7 3-Blade Prop (T-28, P-51)
| Dynam 11x7 3-Blade Prop (T-28)
|
DY-EP-3Blade-11x7
$7.99
Bob Smith Industries 314 Replacement Top for Pocket CA Glues
| Bob Smith Industries 314 Replacement Top for Pocket CA Glues UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.
Works Best On:
Avaliable in 1 oz Size.
|
BSI-314
$0.79
89" Glider-Tow/Trainer (2.25M) Scale Wilga PZL-104 (30-35cc) ARF-Blue
50cc Monsun 102" The Monsun is an exciting airframe to look at and just spectacular to see in the air. Complete with step ladder, navigation and landing lights, front wheel steering, and more! The 50cc Monsun is a masterpiece that will amaze you and your friends at the flying field. Get ready for a new flying experience!
Features:
|
SS-Wilga-35-Blue
$489.99
