DA-170cc Gas Engine

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible PPM 8-Channel Receiver + Lemon DSMX Compatible Satellite with Failsafe

 

Type:	DSMX Compatible PPM 8-Channel Receiver
Number of Channel:	8 (PPM signal)
Modulation:	DSMX Compatible (Also DSM2 backward Compatible)
Band:	2.4 GHz
Dimension:	25(L) x 35(W) x 7(H)  mm
Weight:	2.8 gram without satellite
Voltage Range:	3.45 - 7.2V

 

Highlight - FailSafe option via press of a button to guranteed the highest level of safety even in the event of RF signal loss - 3 microprocessors based system to ensure the highest performance available - Designed especially for Copter high current drain application.

Understanding the receiver

   

 

Setup Instruction

Note: It is highly recommend user to enable FailSafe. Some copters' controller does not have fail-safe system implemented. At the case where the quad copter has flown very far away from the transmitter (eg. 2 km away from transmitter for Aerial photography application), RF signal may have faded due to far distance. FailSafe allows the receiver to output default signal when signal is lost to keep the quad copter flying until signal is recovered again.

Binding Setup

1. Plug bind plug to the receiver.
2. Provide power to the unit. LED flashes quickly.
3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
4. Remove bind plug.

Setting Failsafe

1. Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
2. Ensure that transmitter and receiver are turned on.
3. Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
4. Set transmitter controls to the desired failsafe positions.
5. Press the side pushbutton to memorize failsafe settings.
6. Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
7. Remove bind plug.
8. Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.

Pulse Sequence

The PPM pulse sequence is in the following order:

1. Throttle
2. Aileron
3. Elevator
4. Rudder
5. Gear
6. Aux1
7. Aux2
8. Aux3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:
Male Deans to Male XT60 Connector

With this Deans to XT connector you can convert a battery with T-Plug to XT-60 on ESC / charger
The connector has many applications and can be used for charger adapter.

Features:

• Male Deans T style plug to Male XT60
• Durable design
• Heatshrink seal

The New RedwingRC T-shirt

Show your Redwing pride at the field and add to your Redwing swag collection!

100% cotton

Available in S, M, L, XL, 2XL, 3XL