RCEXL Pro Smoke Pump System

Contact UsCustomer Reviews
  0  
  4. RCEXL Pro Smoke Pump System

RCEXL Pro Smoke Pump System

Ask a question about this product
Printable version

Share

Options

Our Price:

$39.99
Quantity (13)

Details

Availability 13 in stock
Weight 0.50 lbs
SKU rcexl-PRO Smoke
Manufacturer RCEXL

Introducing the Pro Smoke Pump System! These light weight pumps are a simple design and economical way to enter the world of smoke aerobatics. 

-All new diaphragm pump provides optimized smoke/gasoline ratio controlled in a reasonable range for sufficient atomization.
-Adopting low power motor, the smoke pump can be directly powered by receiver. No need for extra batteries. The pump weighs only 85g.
-Directly driven mode, no need of complicated program settings, just need 1 channel for controlling. 

Basic Set up:

First connect the pump to the receiver, fuel filters, muffler and smoke tank (see drawing to help with this).Plug your radio connector into the switched channel (such as landing gear or flaps). Turn on radio, make sure switch is off (100% negative) for at least 5 seconds and turn on. If the pump pushes fluid toward the muffler, the set up is correct. If it tries to pump toward the tank, reverse the wires connected to the receiver.

Radio Set up:

Non programmable Radios

Use a switched channel to switch the Smoke pump on and off. Since there is no trim control on a switched channel, the flow rate is consistent. When the switch is on, flow will be at maximum. We can set the END POINT/ATV of radio switch channel to control the maximum flow rate so as to control the smoke density.

Programmable Radios

Plug the smoke signal wire into a spare channel (such as the 8th channel). Set this channel program mixing the Throttle channel, then set a switch for programming mixing on/off to control smoke pump on/off. Adjust the END POINT/Travel of this channel to control smoke pump flow rate so as to control the smoke density. For more detailed information please see your radio manual.

Specifications:

  • Dimensions(L*W*H): 56*22.5*35.5mm
  • Weight: about 68g
  • Pump Style: Membrane
  • Voltage: 4.8-8.4V
  • Barb Connection: 3mm

Smoke Pump Instructions:








: *
: *
: *
 
DLE 20cc Engine

DLE 20cc Engine

+ Free Shipping (Continental US only!) If international customer, please contact us for shipping quote. You will be charged separately for shipping.
+ Free 2 Year warranty

 

 

Description:
Glow power isn't the only option anymore. The DLE-20 not only fills the displacement gap, but includes a beam mount to make the glow-to-gas upgrade drop-in fast and easy. A rear pumper carb simplifies installation and adjustment of the DLE 20cc. A generous package of "extras" and electronic ignition for starting ease and top performance make the DLE 20 an attractive alternative to glow…and a solid buy for value and performance.

We supply a free 2 year warranty with our DLE 20, and also back it with our in house repair of DLE engines.



Download DLE 20 Manual



Specifications:

  • Stock Number: DLEG0020
  • Displacement: 20 cc (1.22 cu in)
  • Bore: 1.3 in (32 mm)
  • Stroke: 1.0 in (25 mm)
  • Weight: 28.9 oz (820 g)
  • RPM Range: 1,750-9,000
  • Output: 2.5 hp @ 9,000 rpm
  • Requires: unleaded gasoline, 2-cycle oil, ignition battery & propeller
  • Includes: electronic ignition, muffler, spark plug, gasket, bolts, throttle arm extension & manual
  • Suggested Propellers: 16x8 17x6
  • Suggested Break-in Prop: 16x8
  • Ignition Battery: 4.8-6.0V NiCd or NiMH, 6.6V LiFe or 7.4V LiPo pack (LiPo use requires voltage regulator.)
  • Compression Ratio: 10.5:1
  • Gas/Oil Mix: Break in with Lawn Boy(or similar non synthetic oil) at 32:1 Ratio per gallon / Use RedLine oil at 50:1 for long term use after break in.
  • Replacement Spark Plug: NGK CM6 (DLEG5510) or equivalent
  • Weight Breakdown: Engine: 22.9 oz (650 g); Muffler: 1.8 oz (50 g); Ignition: 4.2 oz (120 g)
  • Recommended Propeller: Hawk "C" type 17x6 (for 3d), 16x8 (sport/pattern)

 

 

RedwingRC Pre-Run
DLE 35ra DLE55


 

 

DLE-20

$249.99

Redwing 2S Lipo Batteries

Redwing 2S Lipo Batteries

Description:

Redwing 2S 2200 mah Lipo Batteries.

These batteries are lightweight with a high density of energy and low internal resistance. Lipo batteries have a long life and will provide the power you need when you need it.

These batteries have the XT60 connector, JR connector, and Balance plug



Specifications:

  • Type: Lipo Battery
  • Weight:
    • 2200mah - 5.2 oz.
  • Size:
    • 2200mah- 10.5cm x 3.5cm x 1.5cm
  • Voltage: 7.4Volts
  • 2 cells (2s)
  • Connectors: XT-60 Connector
  • Also a balancing lead
  • 2200mah - $14.99

LiPo-2s-

$9.99

SmartDesign V3 "Trouble Free" Tail Wheel Assembly

SmartDesign V3 "Trouble Free" Tail Wheel Assembly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

This tail wheel assembly is extremely efficient and reliable. With fewer parts, there is less to worry about and the solid construction makes it the go-to choice for pilots at any skill level. The new V2 design incorporates ball bearings for smooth motion, ball-joint to rudder steering connection, wider CF mounting plate, and slightly larger wheels that the v1. "Trouble Free" means just that... no more worrying about screws falling out or loss of control. Make the switch today by installing the SmartDesign Tail Wheel!!!

CNC Aluminum & C.F. Tail Wheel Assembly for 20cc to 220cc

 


 

Features:

 

  • Extremely Reliable
  • Mechanically Efficient Design
  • Simple and Solid Construction
  • Fewer parts needed for install
  • Ball Bearings

 

Pricing

 

  • 20-40cc: $27.00
  • 50-70cc: $34.99
  • 85-120cc: $44.99
  • 150cc-220cc: $54.00

 

 

Weight

 

 

  • 20-40cc: 1.2 oz
  • 50-70cc: 1.6 oz
  • 85-120cc: 2.2 oz
  • 150cc-220cc: 2.6 oz

Don't forget to check out our Aluminum Hub Wheels! They are excellent replacements for landing gears and tail wheels. Please see sizing chart below.

Tail Wheel Chart

GW-KAGC-112

$54.99


Back to Top