Bat-Safe 12" Balancing Cable Extension Set (5)
Description: JST-HX Balance Wire Set for Bat-Safe and Bat-Safe XL The Bat-Safe Balance Cable Set consist of five 12” long Balance Extension wires with JST-XH connectors that can be used for LiPo balancing, charging, or discharging. Any charger that uses an XH balance board or plug can accept these extensions and is a perfect solution moving the battery away from the charger and use for the Bat-Safe charging boxes. The package includes the following extensions (these can be interconnected for extended lengths):
1 set required for your regular size Bat-Safe Battery Charging Safe Box, as standard balancing wires are too short! 12 inches (300mm) long. For the New Bat-Safe XL Battery Charging Safe Box, requires 2 sets of balance wires for a total length of 24 inches (600mm) long. These 12" extensions can also be used as JST extensions for your aircraft allowing pilots to mount a LiFe battery to an inaccessible area and route the wire to an area where it can easily be balanced charged (for example, mounting it to the firewall and then using the extension to route it to the fuselage where you can easily connect it to a balance charger). |
BAT-SAFE XL Lithium Battery Charging Box
BAT-SAFE XL Lithium Battery Charging Box
Description: This flame retardant bag is a convenient way of safeguarding your LiPo batteries during charging, transit, and storage. Just place your battery or batteries in the bag, route the charge wires through the vents at either side of the top flap, and close the flap. ***Please Note: The use of a LiPo Guard is intended to reduce damages in an accident and will not necessarily prevent damage to surrounding objects. Never charge batteries unattended and please follow all safe charging and storage practices.***
Dimensions:
|
BAT-SAFEXL
$139.99
BAT-SAFE Lithium Battery Charging Box
BAT-SAFE Lithium Battery Charging Box ag is a convenient way of safeguarding your LiPo batteries during charging, transit, and storage. Just place your battery or batteries in the bag, route the charge wires through the vents at either side of the top flap, and close the flap. ***Please Note: The use of a LiPo Guard is intended to reduce damages in an accident and will not necessarily prevent damage to surrounding objects. Never charge batteries unattended and please follow all safe charging and storage practices.***
Dimensions:
|
BAT-SAFE
$79.99
24" Charge/Balance Lead Extension Kit
24" Charge / Balance Lead Extension Kit8-Function Charge Adapter to Male 4mm Bullets-300mm Wire Racer's Edge provides an ideal solution for enthusiasts with multiple models using batteries with various connectors. This convenient charging squid comes equipped with virtually every possible connector that a modeler may require. Plugs included: Tamiya, Deans, TRX, XT60, JST, EC3, universal receiver pack, and if we've forgotten anything there is a pre-tinned pair of wires awaiting installation of your favorite connector. |
EX-HRP-RCE1615
$17.99
HUBSAN X4 107L RTF
HUBSAN X4 107L This quadcopter is Ready-To-Fly right out of the box. Suitable for indoor and outdoor flying. The 6-axis flight control system allows the Hubsan X4 to maintain stable flight even in light wind conditions.
Meet the Hubsan X4 Setup and Operation
Promo Video
|
Hubsan X4-
$39.99
BMS-2109, HV-DIGITAL, HIGH TORQUE, ULTRA HIGH SPEED, CORELESS, TITANIUM GEARS
BMS-2109, HV-DIGITAL, HIGH TORQUE. HIGH SPEED, CORELESS, TITANIUM GEARS |
BBR-BMS-2109
$50.00
Bob Smith Industries 304 Pocket CA Extender Tips for Pocket CA Tops (6 Pack)
Bob Smith Industries 304 Pocket CA Extender Tips for Pocket CA Tops (6 Pack) UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.
Works Best On:
Avaliable in 1 oz Size.
|
BSI-304
$2.99