Zap CA Glue (Thin) 1/2oz and 1/4oz (Pink Label)

Description:
The HS-5645MG is one of the best choices you can make for a 50cc sized plane for the cost. They will also work well in 30cc planes. It is fully programmable using Hi Tec's programmer. The combination of torque, speed, price and extreme holding power make it a favorite among pilots. Special alloy gears called “Alumite” offer tremendous strength yet are lightweight as well.


Specifications:

• Torque:
  • 143 oz/in at 4.8V (10.3 kg/cm)
  • 168 oz/in at 6V (12.1 kg/cm)
     
• Speed:
  • .23 sec at 4.8V
  • .18 sec at 6V
     
• Voltage: 4.8V - 6V
• Weight: 2.11oz (59.82g)
• Size: 40.6 x 19.8 x 37.8mm (1.59 x 0.77 x 1.48in)
   
• Motor Type: 3 Pole Ferrite
• Bearing Type: Dual Ball Bearing
• Gear Type: 3 Metal Gears and 1 Resin Metal Gear
• Connector Wire Length: 11.81" (300mm)
• Control System: +Pulse Width Control 1500usec Neutral
• Required Pulse: 3-5 Volt Peak to Peak Square Wave
• Operating Temperature Range: -20 to +60 Degree C
• Operating Angle: 45 Deg. one side pulse traveling 400usec
• 360 Modifiable: Yes
• Direction: Clockwise/Pulse Traveling 1500 to 1900usec
• Dead Band Width: 8usec
• Potentiometer Drive: Indirect Drive
• Current Drain (4.8V): 8.8mA/idle and 400mA no load operating
• Current Drain (6.0V): 9.1mA/idle and 500mA no load operating

Untitled Document

Description:

Bob Smith Industries Insta-Set

Insta-Set™

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

Directions:

After joining parts with cyanoacrylate (CA, super glue), spray the seams with Insta-Set™ to cure the CA in 8 seconds. A bead of CA can then be applied to the outside and corners of joints before another application of Insta-Set™ to reinforce their strength. Insta-Set™ can also be applied to one part (with CA on the other) before joining for difficult to bond materials. Insta-Set™ is compatible with all surfaces, including clear plastic and all foams. It also is a great cleaning agent for adhesive residue and scuff marks. Store separately from CAs.

Works Best On:

Click to Download Safety Data Sheet

• All Cyanoacrylates

EC5 Connectors 

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR