Whoops have gone to the next level! The Mobula7 has taken the internet by storm given its speed and capabilities in such
a small package. Check out the videos and specs of the Mobula 7 by HappyModel below! Features: - New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
- 2S whoop more powerful and more flight time
- Betaflight support , multi flight mode: ACRO/AIR/ANGLE
- New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
- Smartaudio ready , change VTX bands, channels via OSD (Note: DSM2/DSMX and Frsky EU-LBT version are Serial-based
receivers, so Smartaudio is not compatible.) - Adjust the settings and the PID of the flight controller via OSD
- DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
- Full telemetry function ready
- Head lights ready
- Camera angle adjustable
- Real Bind and Fly version
- Buzzer Ready
Specifications: - Brand Name: Happymodel
- Model: Mobula 7
- Item Name: 75mm Wheelbase 2S Brushless Whoop FPV Racing Drone
- Wheelbase: 75mm
- Version: Basic Version (Clear Frame)
- Receiver: Compatible DSM2/DSMX Receiver
- Size: 98mm*98mm*36mm
- Weight: 25.9g (without battery)
Note: This BNF version comes without a transmitter radio (remote controller).
Compatible with Frsky radios or Multi-Protocol radio Package list: 1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Fixing Mount for Lipo Battery
1x Propeller Disassemble Tool
1x Screwdriver Tuning your Mobula7: Your Mobula7’s flight controller controls its flight through settings known as PIDS. Changing these changes the characteristics
of your quad’s flight. RWRC’s recommended Mobula7 tune is: set p_pitch = 65
set i_pitch = 80
set d_pitch = 50
set f_pitch = 96
set p_roll = 65
set i_roll = 80
set d_roll = 50
set f_roll = 96
set p_yaw = 65
set i_yaw = 75
set d_yaw = 0
set f_yaw = 100 To setup this tune, connect your Mobula7 to betaflight and click the CLI tab. Copy and paste the above settings in, hit enter,
type save, then hit enter again. Enjoy your Mobula’s improved flight characteristics! The new betaflight configurator 10.5.0 and 10.5.1 are not compatible with Mobula7 and Mobula7 HD for now. HappyModel suggests using Betaflight configurator 10.4.0 | Crazybee F3 Pro Flight Controller | Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Different version having different receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current meter scale set to 1175
Built-in 5V 1A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Firmware
(Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR
(Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
(DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX
(Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
| | Onboard 5A 4 In 1 ESC | Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v)
MCU upgraded to EFM8BB21
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7
Default protocol: DSHOT600 | | Onboard Frsky NON-EU receiver Version |
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
| Onboard Frsky EU-LBT Version
(External XM+ receiver)
| Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI | | Onboard Flysky receiver Version |
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
|
Onboard DSM2 / DSMX receiver version |
Serial bus receiver
Protocol: DSM2/DSMX compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
| | SE0802 16000KV Motor |
Model: SE0802
KV: 16000KV
Configu-ration: 9N12P Stator Diamter: 8mm Stator Length: 2mm Shaft Diameter: Φ1.0 Motor Dimension (Dia.*Len) : Φ10.5*14.5mm Weight: 1.8g
Support 1-2S Lipo
No.of Cells: 1S Lipo | | Propeller |
40mm 4-blade Propeller ( 4 CW + 4 CCW)
|
5.8G VTX AIO Camera
|
5.8G 40CH 25mW VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
700TVL FOV120 Camera
Camera resolution: 700TVL
Field of view: 120°
Video Format: NTSC
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible)
Size: 13.9"12.0mm ( L*W )
Weight: 3g
| | Lipo Battery |
Capacity:250mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 55mmx12mmx7mm
Weight: 6.5g
Connector: PH2.0
Notes: Need 2pcs batteries for Series circuit
| | 
