UP8 AC 400W / DC 600W 16A x2 Dual Channel Output 1-6S Battery Charger/Discharger/Balancer/Tester
UP8 AC 400W / DC 600W 16A x2 Dual Channel Output 1-6S Battery Charger/Discharger/Balancer/Tester Features:
Specifications:
Add the D200 15A/200W Discharger (use with UPTUP6PLUS, UPTUP7 or UPTUP8) use the drop down to add it to order. The D200 is an external discharger specially designed for use with the UP7 or UP8 chargers. It must be connected to the UP7 or UP8 charger in order to discharge a LiPo battery. The maximum discharge power is 200W, and the discharge current range is 0.1-15.0A. |
Temperature Sensor Cable for Ultra Power Chargers
Description:
Features:
Package Contents:
|
UPTUPTS02
$9.99
4S Pulse LiPo Batteries
Description:Pulse Lithium Polymer Batteries - Setting a New Standard. As Lithium Polymer battery technology continues to push new boundaries, Pulse Lithium Polymer Batteries bring a whole new element into the mix - power & performance at a price that simply can't be ignored. Pulse Batteries Available Individually or in a PRE-MADE System!Take the guesswork out of your electric battery set up- we've done it for you! Check out the suggested set up systems for 30cc and 50cc. LiPo 4500mah 5S, 18.5v - $104.99 each 30cc 10S System: Two (2) LiPo 4500mah 5S, 18.5v - $208
30cc 12S System #1: Two (2) LiPo 3300mah 45C 6S, 22.2v - $188
30cc 12S System #2: Two (2) LiPo 3700mah 45C 6S, 22.2v - $218
30cc 12S System #3: Two (2) LiPo 4100mah 45C 6S, 22.2v - $238
50cc 12S System #1: Two (2) LiPo 5000mah 45C 6S, 22.2v - $278
50cc 12S System #2: Two (2) LiPo 5500mah 45C 6S, 22.2v - $298
50cc 12S System #3: Two (2) LiPo 6000mah 35C 6S, 22.2v - $298
Purchase pre-made system or buy individually! Select below.
|
PLU-4
$47.49
Pulse CellMeter 8 - Lipo Battery Checker & Servo Tester
Description:The Pulse CellMeter-8 is the latest version of battery testers - and is now available to our Redwing customers! If you want a new, easy to use, digital battery and capacity tester, your search is over. The Pulse CellMeter-8 can check the overall and individual voltage of 2 through 8 celled, LiPo / LiFe / Li-Ion batteries and 4 through 8 celled, Nicd / NiMH batteries - as well as instantly provide you with your remaining capacity. Did I mention that happens INSTANTLY? We can't make this stuff up. This nifty little checker does more than that! The cell button allows you to balance your packs as well. So this isn't your typical bettery tester - but a balancer built in.
Features:
Specification:
|
PLU-CELLMETER8
$14.99
PULSE 3S 22000mAh 11.1V 5C Charging Power Bank - Not Designed for Flight
Description:
Features:
Package Contents:
|
PLU5-220003
$235.99
HUBSAN X4 107L RTF
HUBSAN X4 107L This quadcopter is Ready-To-Fly right out of the box. Suitable for indoor and outdoor flying. The 6-axis flight control system allows the Hubsan X4 to maintain stable flight even in light wind conditions.
Meet the Hubsan X4 Setup and Operation
Promo Video
|
Hubsan X4-
$39.99
BMS-2109, HV-DIGITAL, HIGH TORQUE, ULTRA HIGH SPEED, CORELESS, TITANIUM GEARS
BMS-2109, HV-DIGITAL, HIGH TORQUE. HIGH SPEED, CORELESS, TITANIUM GEARS |
BBR-BMS-2109
$50.00
Bob Smith Industries 304 Pocket CA Extender Tips for Pocket CA Tops (6 Pack)
Bob Smith Industries 304 Pocket CA Extender Tips for Pocket CA Tops (6 Pack) UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.
Works Best On:
Avaliable in 1 oz Size.
|
BSI-304
$2.99