HiTec 9380 Digital Brushless Servo (34kg/472oz [email protected])
With ultra-efficient brushless motors, titanium gear trains, low current consumption and constant output power, the HSB-93XX series of servos is the perfect match for the most discriminating pilots and racers. FEATURES
PROGRAMMABLE FUNCTIONS
ACCESSORIES
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Performance Specifications | |
| Operating Voltage Range (Volts DC) | 6.0V ~ 7.4V |
| Speed (Second @ 60°) | 0.17 ~ 0.14 |
| Maximum Torque Range oz. / in. | 472 |
| Maximum Torque Range kg. / cm. | 34 |
| Current Draw at Idle | 27 mA |
| No Load Operating Current Draw | 250 mA |
| Stall Current Draw | 2,100 mA |
| Dead Band Width | 1 µs |
| Physical Specifications | |
| Dimensions (Inches) | 1.57 x 0.79 x 1.50 |
| Dimensions (Metric) | 40.0 x 20.0 x 38.0 |
| Weight (Ounces) | 2.4 |
| Weight (Gram) | 68.0 |
| Circuit Type | EBL Digital |
| Motor Type | Brushless |
| Gear Material | Titanium |
| Bearing Type | Dual Ball Bearing |
| Output Shaft (type / Ømm) | H25T |
| Case Material | Plastic / Aluminum |
| Dust / Water Resistance | Splash Proof |
| Connector Gauge (AWG) / Strand Count | 20 / 80 |
| Radio Control Applications | |
| Parkflyer | N / A |
| Sport Plane | > 40% |
| Sailplane | 2 meters and up |
| 3D Performance | > 40% |
| Scale | > 40% |
| Electric Helicopter | N / A |
| Gas Helicopter | N / A |
| On Road | N / A |
| Monster Truck | 1/8th |
| Buggies | 1/8th |
| Truggies | 1/8th |
| Short Course / Truck | 1/8th |
| Crawlers | N / A |
| Sail Boat | = >1M & Scale |
| Power Boat | 1/10th |
HiTec 9380 Digital Brushless Servo
Servo Extensions 22AWG and 20AWG
| High quality 22AWG wire, twisted silicone wire extensions. JR type connections, so they will plug into any receiver/switch, and most servos (Hitec/JR/PowerHD/etc etc....futaba you would have to trim the edge off).
|
EX
$2.50
Bob Smith Industries 303 Extra-Long Extender Tips Multi-Use for CAs
| Bob Smith Industries 303 Extra-Long Extender Tips Multi-Use for CAs UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.
Works Best On:
Avaliable in 1 oz Size.
|
BSI-303
$0.49
Venom DRIVE 35C 3S 5000mAh 11.1V LiPo Hardcase Battery with UNI 2.0 Plug
| Venom DRIVE 35C 3S 5000mAh 11.1V LiPo Hardcase Battery with UNI 2.0 Plug |
VNR15128-RW
$72.99
