Power HD 1501MG (235 oz/17.00 kg at 6V)

Description:
Our LiFe Batteries (also known as A123 Batteries) have huge advantages over most other options.

1) LiFe Batteries are lightweight - as light as Lipos
2) LiFes are safer than Lipos (do not combust easily like lipos)
3) LiFe Batteries supply a constant voltage (They stay right near 6volts from start to finish ensuring consistent flights)
4) Run Life batteries to your servos and ignition without regulators (For extra caution some people run a regulator to their ignition still)
5)Life's have a high Charging Capacity. Charge up to 5amps, allowing you to charge them up in MINUTES!

The 2100 or 3000 Mah can be used as a SINGLE battery system for 30cc planes. (we recommend spliting the lead and put 2 JR leads on, to run to the receiver and the other to ignition). You can also run a single 3000 Life Battery on a 50cc Plane.

The 1450mah LiFE Battery is a great option for those that want a separate battery for ignition and receiver (if you are running FM or hesitant to use a single battery system). The 1450mah Life is a great battery for the ignition for either a 30cc or 50cc sized plane

We recommend the following:
On the MXSR (2) 2100mah, or 1 3000mah placed on the mount box or front of the plane. It is a bigger plane and will do well with the extra voltage and weight.
Other 30cc planes - (1) 1450mah for ignition, (1) 2100mah for receiver or for a lighter set up
(1) 2100mah for both (split the wire to 2 leads) OR (2) 1450mah (one for ignition one for receiver).

50cc sized planes (1) 1450mah LiFe battery for ignition and (1) 3000mah LiFe battery for receiver or, for a lighter set up
(1) 1450mah for ignition, and (1) 2100 for receiver OR (1) 3000mah LiFe for both receiver and ignition



WATCH THIS VIDEO: Explains whether to use a regulator or not, 2 batteries or 1 for your plane, Redundancy and more.


Specifications:

• Type: LiFe Battery (same technology as A123)
• Weight:
  • 1450mah - 2.8oz,
  • 2100mah - 4oz,
  • 3100mah Life - 5.5oz
• Size:
  • 1450mah- 15mm x 34mm x 87mm,
  • 2100mah- 12mm x 50mm x 106mm,
  • 3000mah- 130mm x 45mm x 15m
• Voltage: 6.6Volts
• Discharge rate:
  • 20c maximum continuous
  • 40c maximum burst
• 2 cells (2s)
• 14gauge Wire
• Connectors: Two Options!
  • T Connector (T connector that fit a standard Dean)
  • XT-60 Connector. Choose Below
• Also a balancing lead

Be sure to select the XT connector if purchasing for use with our Power Box PRO's. Please select connector type: Deans or XT.
 

• 1450mah - $15.99
• 2100mah - $25.99
• 3000mah - $39.99
   

Description:

The Power HD LF-20 MG is excellent for a 30cc or 50cc plane. This Digital servo has metal housing around the middle which allows for the heat to rapidly dissipate. With double ball bearings you will have smooth movement and powerful torque when you need it. You cant beat the performance of this servo and at such a great price it's a no-brainer.

The Power HD LF-20 servos are a PERFECT Bargain servo with respectable performance. If you are looking for a top notch budget servo that has better centering and resonlution, you may consider the 8309/8312 Power HD servos, but for this price you won't find a better servo!

Specs:

• Torque:
  • 229.1 oz/in at 4.8V (16.5 kg/cm)
  • 277.7 oz/in at 6.6V (20.0 kg/cm)
     
• Speed:
  • .18 sec at 4.8V
  • .16 sec at 6.6V
     
• Voltage:
• Weight: 2.12 oz (60g)
• Size: 1.60 x 0.80 x 1.55 in ( 40.7 x 20.5 x 39.5 mm)
   
• Operating Voltage - 4.8 ~ 6.6 DC Volts
• Operating Temp- -20~60centigrade
• Working Frequency - 1520μs / 333hz
• DC Motor
• Middle Aluminum Casing With Plastic Top and Bottom
• Double Ball Bearings
• Copper & Aluminum Gears
• Wire length- 300cm

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

• Balsa Wood
• Ceramics

Works Good On:

• Soft Wood
• Fiberglass
• Hard Plastics
• Water-Resistant
• CA Hinges

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet