Power Board - PRO SERIES - Red (4104)
All NEW 4000 SERIES! *with Digital Readout and Touch-button programming. Description: Completely redesigned from the ground up, with these new Power Boards you are able to use 2 batteries with redundancy to avoid possible crashes from battery failure. Simply plug in your batteries with XT-60 style connectors to this Power Board Expander (Our LiFe batteries are perfect for this) and you now have 2 batteries working in tandem to supply your servos AND ignition. These new versions offer SEVERAL new features: 1) Digital read out on all models - displaying voltage going IN and OUT of all devices (see photo) 2) LED and audible alarm for all models that you can set to warn when your system drops below a voltage of your choosing 3) TOUCH button programming to select your warning voltage 4) Wires to your RX are PRE-installed 5) Enclosed lightweight and strong plastic housing 6) XT-60 Connectors The Power Board board electronically isolates the batteries from each other so that there is no interference possible from your ignition. It also regulates the voltage down to an ideal voltage to your RX (5v) and then is select-able to your servos (yellow and black units only - the red unit offers the same voltage as your batteries to the servos). They feature a mounting space in the middle to mount your RX and also include mounting hardware to mount it securely to your plane.
|
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Power Board - PRO SERIES - Red (4104)
Distribution Panel (Power Board) Switch with Voltmeter
| switch, Distribution Panel (Power Board) Switch, RCCSKJ |
Rccskj-DP-switch-2105
$17.99
Servo Extensions 22AWG and 20AWG
| High quality 22AWG wire, twisted silicone wire extensions. JR type connections, so they will plug into any receiver/switch, and most servos (Hitec/JR/PowerHD/etc etc....futaba you would have to trim the edge off).
|
EX
$2.50
Rcexl Walbro Style Weighted Felt Fuel Clunk
| Rcexl Walbro Style Weighted Felt Fuel Clunk Fuel clunks are a must for aerobatic flying. It insures that fuel is always flowing to the engine because the fuel line will follow gravity inside your tank. Without one, you increase the chance that your plane may stall when flying inverted or performing different maneuvers. Installing a fuel clunk is simple to install and an investment that any serious pilot should make. 13x16mm .4 oz |
Rcexl-Fuel-Clunk
$5.99
Zap Z-Ends (10pcs) & Teflon Tubing
| Zap Z-Ends (10pcs) & Teflon Tubing
Description:Bob Smith Industries CA Glue Super-Gold+™ Odorless, CASUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
Works Best On:
Works Good On:
Avaliable in 2oz and 3/4 Pocket Size. Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.
|
PT-18
$4.99
