Switches and Wires

Description:
1 piece: 2S JST Male to Female Extension

This is a 12" extension for JST connections. This will allow you to mount your LiFe battery to an inaccessible area and route the wire to where you can easily balance charge it as needed. (for example, mounting it to the firewall and then using the extension to route it to the fuselage where you can easily connect it to a balance charger

Fully compatible with Redwing RC LiFe batteries

1 Male to Female JST 12" extension
 

Description:

MPI Charge switch with LED indicator for HiTec and JR leads and on-board battery checker! The three LEDs - green, yellow, & red - monitor the status of the flight pack. It is designed to test the battery under the actual load of the on-board equipment.

The switch is factory preset to 4.8V applications - but for 6V use, simply cut the jumper loop on the back of the switch and seal the wires with silicone glue or tape. The jumper wires can be reconnected for 4.8V operation.

Features:

• Heavy duty switch and wires
• Sturdy one-piece design
• Built-in Redundancy
• 3-LED on-board battery checker
• Compatible with 4.8v and 6v Rx packs
• Easy installation and operation
• Silicone shock mount included
• DSC compatible

XT60 Parallel Connector XT60 Female to 2 XT60 Male Adapter

Description:
Male Deans to Male XT60 Connector

With this Deans to XT connector you can convert a battery with T-Plug to XT-60 on ESC / charger
The connector has many applications and can be used for charger adapter.

Features:

• Male Deans T style plug to Female XT60 (adapter for XT60 power Boards to convert to Deans)
• Durable design
• Heatshrink seal

Description:

Short 3 wire to keep tangled wires to a minimum when charging batteries outside of your plane. You can still charge the batteries inside your plane as long as you can get the charger relatively close to the wire or port. Ideal for a multi charger since you won’t have 4 or more super long wires getting tangled and twisted as you try to charge your batteries.

Description:

Short 3 wire to keep tangled wires to a minimum when charging batteries outside of your plane. You can still charge the batteries inside your plane as long as you can get the charger relatively close to the wire or port. Ideal for a multi charger since you won’t have 4 or more super long wires getting tangled and twisted as you try to charge your batteries.

Description:

Short 3 wire to keep tangled wires to a minimum when charging batteries outside of your plane. You can still charge the batteries inside your plane as long as you can get the charger relatively close to the wire or port. Ideal for a multi charger since you won’t have 4 or more super long wires getting tangled and twisted as you try to charge your batteries.

Description:

Short 3 wire to keep tangled wires to a minimum when charging batteries outside of your plane. You can still charge the batteries inside your plane as long as you can get the charger relatively close to the wire or port. Ideal for a multi charger since you won’t have 4 or more super long wires getting tangled and twisted as you try to charge your batteries.

Description:

3” male to male servo extension. This wire allows you to easily and quickly convert an item ending in a female plug to a male. This often has applications in our hobby, allowing you to essentially change the plug at the end of your battery or other electronics from a female to a male without having to cut and re-solder

Description:

3” Female to female servo extension. This wire allows you to easily and quickly convert an item ending in a male plug to a female. This often has applications in our hobby, allowing you to essentially change the plug at the end of your battery or other electronics from a male to a female without having to cut and re-solder.

Description:

Booma RC pin flag switch for IntelliReg, Smart-Fly or Gryphon regulator. This pin flag switch Booma RC is an ultra high quality fail safe switch designed as a replacement switch for Smart-Fly systems, Power System, Power Expander, Regulators as well as Gryphon Heli regulators.

Supplied with 1 x switch actuator and 1 x pin flags.

Power Board - PRO SERIES - Red (4104)

All NEW 4000 SERIES! *with Digital Readout and Touch-button programming.

Description:

Completely redesigned from the ground up, with these new Power Boards you are able to use 2 batteries with redundancy to avoid possible crashes from battery failure. Simply plug in your batteries with XT-60 style connectors to this Power Board Expander (Our LiFe batteries are perfect for this) and you now have 2 batteries working in tandem to supply your servos AND ignition.

The Power Board board electronically isolates the batteries from each other so that there is no interference possible from your ignition. It also regulates the voltage down to an ideal voltage to your RX (5v) and then is select-able to your servos (yellow and black units only - the red unit offers the same voltage as your batteries to the servos).

You can Plug in, up to 8 servos into the board (12 servos with the Black Power Board), which has 2 outputs for EACH channel, effectively DOUBLING the number of servos you can use in a plane ( a total of 16 output channels) without reducing the amperage (that a Y cable would cause).

These Power Boards also features LED lights to give you clear indication that your batteries are connected and working properly, as well as voltage etc.

They feature a mounting space in the middle to mount your RX and also include mounting hardware to mount it securely to your plane.





Watch this video for an overview of the different versions


View this video for a full explanation on how to use these power boards




Features:

Red Power Board (4104)

• Dual battery redundancy for safer flying
• LCD display which shows real time info of your in and out voltages
• Built in regulator that supplies a clean 5v to your receiver
• Integrated CDI remote cut off switch to kill your engine (OPTO KILL)
• 8 channels in, 16 channels out (+ ignition)
• Electronically isolated for interference free flying
  
  (We recommend our LiFe batteries and 6v servos with this unit - be sure to select ones with XT connectors for this use)

Specs:

Red Power Board (4104)

• Input Voltage: 5-13v
• Working load: 0A to 20A
• Weight: 3 oz.
• Dimensions: 4.5"x2.5"x5/8"
• Working Temperature: -20c to -85c

Recommended Set ups: Use the Red Power Board for 30-50cc planes using 6v servos. Use 2 LiFe batteries, and "jump" power down from an open servo port on the board, to run to your ignition