Align TN70 Nitro Helicopter KIT (with Pipe)

Ask a question about this product

Printable version

Options

Our Price:

$809.00

Quantity (1)

Details


Availability	1 in stock
Weight	5.00 lbs
SKU	Heli-RH70N36XT

RH70N31XW

Electric equipment

●ALIGN 105 High Performance Pipe x 1
●Governor Sensor x 1

Specification

●Length: 1352mm
●Height: 397mm
●Width: 202mm
●Main Blade Length: 690mm
●Main Rotor Diameter: 1543mm
●Tail Rotor Diameter: 279mm
●Tail Drive Belt Pulley:27T
●Main Drive Gear:107T
●Autorotation Tail Drive Gear: 102T
●Tail Drive Gear: 23T
●Drive Gear Ratio: 7.43:1:4.23
●Engine: 105 Nitro Engine
●Fuel Tank Capacity: 630cc.
●Takeoff Weight: Approx. 4110g

Accessories

●TN70 Kit Set x 1 set
●690 Carbon Fiber Blades x 1 set
●105 Carbon Fiber Tail Blades x 1 set
●ALIGN 105 High Performance Pipe x 1
●Governor Sensor x 1

Radio transmitter and electronic equipment required for assembly

●Transmitter(7-channel or more, helicopter system)
●Receiver(7-channel or more) or Remote Receiver
●Flybarless System x1
●Engine starter x 1
●Fuel pump x 1
●105 Engine x 1
●Engine fuel x 1
●DS830M High Voltage Brushless Servo x 3
●DS835M High Voltage Brushless Servo x 1
●DS530 Digital Servo x 1
●B6M 2 In 1 Voltage Regulator Combo x 1
●Digital Pitch Gauge
●Multi-function Tester
●2S1P 7.4V Li-Po 1900~2600mAh Battery x 1

Flat rate $20 Shipping lower 48 USA only! Contact us at [email protected] for international shipping costs.

KST BLS915 V2 Brushless Standard Servo For 550-700 Helicopters

Description:

Ever go to a restaurant and look at the menu and think to yourself - "there's so many options that all just look so good!" - and have trouble deciding? Well here at Redwing RC our awesome servo collection is very similar! We have a great variety of spectacular servos to choose from so there is something for everyone! But let's introduce yet another great option to consider --

This is the Xpert AS-6501-HV A2 Standard Size Aluminum Servo.

Torque

– @8.4V: 348.94 oz-in/ @8.4V: 25.14 kg-cm

– @7.4V: 304.95 oz-in/@7.4V:21.97 kg-cm

Speed

– @8.4V: .096 sec/45°

– @7.4V: .104 sec/45°

Dimensions: 40x20x37.8mm

Weight: 71g

Matching Gear Set: XGS73780

GET YOURS TODAY!

PRS-BLS915V2

$85.00 85.00

Bob Smith Industries 302 Extra Fine Extender Tips for CA Glue Bottles (6 Pack)

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.