Products Map - RedwingRC.com

Contact UsCustomer Reviews

Products Map

Lemon RX DSMX Compatible PPM 8-Channel Receiver w/Satellite with Failsafe

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible PPM 8-Channel Receiver + Lemon DSMX Compatible Satellite with Failsafe

 

Type: DSMX Compatible PPM 8-Channel Receiver
Number of Channel: 8 (PPM signal)
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 35(W) x 7(H)  mm
Weight: 2.8 gram without satellite
Voltage Range: 3.45 - 7.2V

 

Highlight - FailSafe option via press of a button to guranteed the highest level of safety even in the event of RF signal loss - 3 microprocessors based system to ensure the highest performance available - Designed especially for Copter high current drain application.

Understanding the receiver

   

 

Setup Instruction

Note: It is highly recommend user to enable FailSafe. Some copters' controller does not have fail-safe system implemented. At the case where the quad copter has flown very far away from the transmitter (eg. 2 km away from transmitter for Aerial photography application), RF signal may have faded due to far distance. FailSafe allows the receiver to output default signal when signal is lost to keep the quad copter flying until signal is recovered again.

Binding Setup

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. Remove bind plug.

Setting Failsafe

  1. Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
  2. Ensure that transmitter and receiver are turned on.
  3. Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
  4. Set transmitter controls to the desired failsafe positions.
  5. Press the side pushbutton to memorize failsafe settings.
  6. Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
  7. Remove bind plug.
  8. Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.

Pulse Sequence

The PPM pulse sequence is in the following order:

  1. Throttle
  2. Aileron
  3. Elevator
  4. Rudder
  5. Gear
  6. Aux1
  7. Aux2
  8. Aux3

LM-0007

$34.99

Lemon RX SATELLITE WIRE 20CM

 

Lemon RX SATELLITE WIRE 20CM

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-P-00047

$2.99

LiFe Batteries 2S

Description:
Our LiFe Batteries (also known as A123 Batteries) have huge advantages over most other options.

1) LiFe Batteries are lightweight - as light as Lipos
2) LiFes are safer than Lipos (do not combust easily like lipos)
3) LiFe Batteries supply a constant voltage (They stay right near 6volts from start to finish ensuring consistent flights)
4) Run Life batteries to your servos and ignition without regulators (For extra caution some people run a regulator to their ignition still)
5)Life's have a high Charging Capacity. Charge up to 5amps, allowing you to charge them up in MINUTES!

The 2100 or 3000 Mah can be used as a SINGLE battery system for 30cc planes. (we recommend spliting the lead and put 2 JR leads on, to run to the receiver and the other to ignition). You can also run a single 3000 Life Battery on a 50cc Plane.

The 1450mah LiFE Battery is a great option for those that want a separate battery for ignition and receiver (if you are running FM or hesitant to use a single battery system). The 1450mah Life is a great battery for the ignition for either a 30cc or 50cc sized plane

We recommend the following:
On the MXSR (2) 2100mah, or 1 3000mah placed on the mount box or front of the plane. It is a bigger plane and will do well with the extra voltage and weight.
Other 30cc planes - (1) 1450mah for ignition, (1) 2100mah for receiver or for a lighter set up
(1) 2100mah for both (split the wire to 2 leads) OR (2) 1450mah (one for ignition one for receiver).

50cc sized planes (1) 1450mah LiFe battery for ignition and (1) 3000mah LiFe battery for receiver or, for a lighter set up
(1) 1450mah for ignition, and (1) 2100 for receiver OR (1) 3000mah LiFe for both receiver and ignition



WATCH THIS VIDEO: Explains whether to use a regulator or not, 2 batteries or 1 for your plane, Redundancy and more.


Specifications:

  • Type: LiFe Battery (same technology as A123)
  • Weight:
    • 1450mah - 2.8oz,
    • 2100mah - 4oz,
    • 3100mah Life - 5.5oz
  • Size:
    • 1450mah- 15mm x 34mm x 87mm,
    • 2100mah- 12mm x 50mm x 106mm,
    • 3000mah- 130mm x 45mm x 15m
  • Voltage: 6.6Volts
  • Discharge rate:
    • 20c maximum continuous
    • 40c maximum burst
  • 2 cells (2s)
  • 14gauge Wire
  • Connectors: Two Options!
    • T Connector (T connector that fit a standard Dean)
    • XT-60 Connector. Choose Below
  • Also a balancing lead

Be sure to select the XT connector if purchasing for use with our Power Box PRO's. Please select connector type: Deans or XT.
 

 

 

  • 1450mah - $15.99
  • 2100mah - $25.99
  • 3000mah - $39.99
     

LXT-2S-1450

$18.99

LiFe Batteries 3S

Description:
Our LiFe Batteries (also known as A123 Batteries) have huge advantages over most other options.

1) LiFe Batteries are lightweight - as light as Lipos
2) LiFes are safer than Lipos (do not combust easily like lipos)
3) LiFe Batteries supply a constant voltage (They stay right near 6volts from start to finish ensuring consistent flights)
4) Run Life batteries to your servos and ignition without regulators (For extra caution some people run a regulator to their ignition still)
5)Life's have a high Charging Capacity. Charge up to 5amps, allowing you to charge them up in MINUTES!

The 2100 or 3000 Mah can be used as a SINGLE battery system for 30cc planes. (we recommend spliting the lead and put 2 JR leads on, to run to the receiver and the other to ignition). You can also run a single 3000 Life Battery on a 50cc Plane.

The 1450mah LiFE Battery is a great option for those that want a separate battery for ignition and receiver (if you are running FM or hesitant to use a single battery system). The 1450mah Life is a great battery for the ignition for either a 30cc or 50cc sized plane

We recommend the following:
On the MXSR (2) 2100mah, or 1 3000mah placed on the mount box or front of the plane. It is a bigger plane and will do well with the extra voltage and weight.
Other 30cc planes - (1) 1450mah for ignition, (1) 2100mah for receiver or for a lighter set up
(1) 2100mah for both (split the wire to 2 leads) OR (2) 1450mah (one for ignition one for receiver).

50cc sized planes (1) 1450mah LiFe battery for ignition and (1) 3000mah LiFe battery for receiver or, for a lighter set up
(1) 1450mah for ignition, and (1) 2100 for receiver OR (1) 3000mah LiFe for both receiver and ignition



WATCH THIS VIDEO: Explains whether to use a regulator or not, 2 batteries or 1 for your plane, Redundancy and more.


Specifications:

  • Type: LiFe Battery (same technology as A123)
  • Weight:
    • 3S 2100mah - 6.2oz
    • 3S 3100mah Life - 9oz
  • Size:
    • 3S 2100mah- 95mm x 29mm x 30mm
    • 3S 3000mah- 130mm x 42mm x 20mm
  • Voltage:
    • 3S 2100- 9.9 Volts
    • 3S 3000- 9.9 Volts
  • Discharge rate:
    • 20c maximum continuous
    • 40c maximum burst
  • 14gauge Wire
  • Connectors: XT-60 Connector
  • Balancing lead

These batteries have the XT-60 connector.
 

 

 

  • 3S 2100mah - $33.99
  • 3S 3000mah - $49.99

****Batteries must ship surface mail due to hazmat restrictions and have been taking longer to reach destination****Express and Priority mail are not an option for surface ground mail.

LXT-3S-2100-XT

$33.99

LiFe Batteries 4S

Description:
Our LiFe Batteries (also known as A123 Batteries) have huge advantages over most other options.

1) LiFe Batteries are lightweight - as light as Lipos
2) LiFes are safer than Lipos (do not combust easily like lipos)
3) LiFe Batteries supply a constant voltage (They stay right near 6volts from start to finish ensuring consistent flights)
4) Run Life batteries to your servos and ignition without regulators (For extra caution some people run a regulator to their ignition still)
5)Life's have a high Charging Capacity. Charge up to 5amps, allowing you to charge them up in MINUTES!

The 2100 or 3000 Mah can be used as a SINGLE battery system for 30cc planes. (we recommend spliting the lead and put 2 JR leads on, to run to the receiver and the other to ignition). You can also run a single 3000 Life Battery on a 50cc Plane.

The 1450mah LiFE Battery is a great option for those that want a separate battery for ignition and receiver (if you are running FM or hesitant to use a single battery system). The 1450mah Life is a great battery for the ignition for either a 30cc or 50cc sized plane

We recommend the following:
On the MXSR (2) 2100mah, or 1 3000mah placed on the mount box or front of the plane. It is a bigger plane and will do well with the extra voltage and weight.
Other 30cc planes - (1) 1450mah for ignition, (1) 2100mah for receiver or for a lighter set up
(1) 2100mah for both (split the wire to 2 leads) OR (2) 1450mah (one for ignition one for receiver).

50cc sized planes (1) 1450mah LiFe battery for ignition and (1) 3000mah LiFe battery for receiver or, for a lighter set up
(1) 1450mah for ignition, and (1) 2100 for receiver OR (1) 3000mah LiFe for both receiver and ignition



WATCH THIS VIDEO: Explains whether to use a regulator or not, 2 batteries or 1 for your plane, Redundancy and more.


Specifications:

  • Type: LiFe Battery (same technology as A123)
  • Weight:
    • 4S 2100 mah 8oz
    • 4S 3000 mah 11.6oz
  • Size:
    • 4S 2100- 95mm x 29mm x 40mm
    • 4S 3000- 130mm x 43mm x 28mm
  • Voltage:
    • 4S 2100- 13.2 Volts
    • 4S 3000- 13.2 Volts
  • Discharge rate:
    • 20c maximum continuous
    • 40c maximum burst
  • 14gauge Wire
  • Connectors: XT-60 Connector
  • Balancing lead

 

 

These batteries have the XT-60 connector.
 

 

 

  • 4S 2100mah - $42.99
  • 4S 3000mah - $56.99

     

LXT-4S-2100-XT60

$42.99

Light Foam Tail Wheel/Tire (30mm 35mm 40mm 45mm 50mm)

3" Micro Sport Wheels 2/pkg

These Lightweight Tires/wheels for RC planes are treaded durable rubber wheels. they offer a strong but light option for your 3d plane and also give you significant shock absorption on landings.

These RC plane wheels are available in 3" and 3.5" sizes. 3" is good for 30cc and similar. 3.5" are good for 50cc and similar sized planes

Weight: Approximately 3oz PER pair

SOLD IN PAIRS

FM-Tail wheel 30mm

$1.75

Lightning 1500 Sport Glider PNP 59" (1500mm)

Lightning 1500 Sport Glider PNP 59" (1500mm)  

top-035B

$149.99

Out of stock

Lightning 2100 High Speed Glider PNP 83" (2100mm)

Lightning 2100 High Speed Glider PNP 83" (2100mm)

top-090B

$199.00

LiPo Guard Charging Bag

Untitled Document

Description:

This flame retardant bag is a convenient way of safeguarding your LiPo batteries during charging, transit, and storage.

Just place your battery or batteries in the bag, route the charge wires through the vents at either side of the top flap, and close the flap. ***Please Note: The use of a LiPo Guard is intended to reduce damages in an accident and will not necessarily prevent damage to surrounding objects. Never charge batteries unattended and please follow all safe charging and storage practices.***

 

Dimensions:

  • Small: 7.25"x 8.75"
  • Large: 9"x11.5"

 

 

GT_LPB1

$9.99

Little Wing, Cool Kite

Little Wing, Spectrum Kite

HRP-SKK20416

$48.99

Little Wing, Spectrum Kite

Little Wing, Spectrum Kite

HRP-SKK20415

$48.99

Loadstar II Model Rocket Kit, Skill Level 2

Rockets

EST3227

$21.99