FUTABA S3071HV S.Bus High Voltage Standard Airplane Servo .17sec/145.9oz @ 7.4V (CLONE)

Description:

All NEW design! These Miracle aluminum spinners have back plates which have extensive lightening, the spinners are cut for a large 3d style prop, and the back plates are drilled for multiple engine sizes!

FOR ENGINE SIZE:

• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 3" Spinner: DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
• 3.5" DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
  
  SPECS:
• 2.5": Height 2.7", weight 2.7oz, includes 30mm bolt.
• 3": Height - 3.1", weight 3.2 oz, includes 55mm bolt.
• 3.5" : Height 3.7", weight 3.6oz, includes 60mm bolt.

Miracle RC Aluminum Spinners are high quality CNC Machined spinners. Very light, with a lightened back plate included. Very accurate, very beautiful, and a great value!

• 2.5" - $16.95
• 3" - $20.95
• 3.5" - $27.95
• 3.75"- $31.95
• 4.0" - $38.95
• 4.5" - $44.95
• 5" - $50.95

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure+™ Super Glue, CA

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning

Works Best On:

• Balsa Wood
• Soft Wood

Works Good On:

• Hard Wood
• Glass & Metals
• Fiberglass
• Ceramics
• Hard Plastics
• Rubber
• Laminating
• Water-Resistant
• Reinforcing

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

Click to Download Safety Data Sheet

mount bracket