BLS-27AWB Water Proof,+Lockable Servo Arm (30.7 kg/426.4oz, 0.05 sec @ 8.4V New generation Servo)

Ask a question about this product

Printable version

Options

Market Price: $145.00

Our Price:

$115.99

You Save

20%

Quantity (7)

Details


Availability	7 in stock
Weight	0.52 lbs
SKU	BBR-BLS-27AWB
Manufacturer	Blue Bird

BLS-27AWB Water Proof,+Lockable Servo Arm (30.7 kg/426.4oz, 0.05 sec @ 8.4V New generation Servo)--Blue Bird's latest generation servo that is water proof and includes soft start, voltage, heat, rotor, and loss of control protections and includes a Lockable Aluminum Servo ARM! Perfect match for 1/8 scale Monster Truck/Crawler/Large Boat or 3D Plane!

Water Proof IP67 (Ingress Protection Rating, 6=Dust Tight, 7=Immersion up to 1M for 30 min)

Features:

★Soft Start Protection
★Over Voltage Protection
★Low Voltage Protection
★Locked Rotor Protection
★Temperature and Loss of signal Protection

APPLICATION / SUITABLE

Perfect for 1/8 Scale Buggy (Off-road), GT (On-Road), Monster Truck, Rock Crawler and Large Boats and 3D plane

ELECTRICAL SPECIFICATION (FUNCTION OF THE PERFORMANCE)

Torque At 6.0V	21.9 kg-cm / 304.2 oz-in
Torque At 7.4V	27.3 kg-cm / 379.2 oz-in
Torque At 8.4V	30.7 kg-cm / 426.4 oz-in
Speed At 6.0V	0.08sec / 60°
Speed At 7.4V	0.06 sec / 60°
Speed At 8.4V	0.05 sec / 60°

PROTECTION MECHANISM

Soft Start Protection	Soft start to neutral position.
Over Voltage Protection	Over 9.0V drive the protection mode and 8.4V return to normal mode.
Low Voltage Protection	Lower than 4.0V, drive the protection mode and 4.5V return to normal mode.
Locked Rotor Protection	Stall in 5 sec, output torque goes down.
Temperature and Loss Signal Protection	Overheat 85 degree C, drive the protection mode and down 75 degree C return to normal mode. Loss of TX signal, servo willreturn to neutral position and lock.

POWER SUPPLY

Operating Voltage Range

4.5V ~ 8.5V ( 4 ~ 6 Cell Ni-MH or 2S LiPo / 2S LiFe)

CONTROL SPECIFICATION

Control System	32-Bits CPU Digital Controller / AD 12-Bits ( 4096 Steps ) Frequency：Up to 333Hz / Neutral：1500us or 1520us
Dead Band Width	0.001ms ( Defualt: 1us )

MECHANICAL SPECIFICATIONS

Ball Bearing	Dual, Stronger Steel Bearings 1 piece oil sealed
Gear	All Steel Alloy Metal Gears
Cable	300mm(~12") Black Cased Cable
Motor	High Premium Brushless Motor
Horn / Gear Spline	25 Teeth ( Same as F-Type)

PHYSICAL SPECIFICATIONS

Dimension (mm)	40.6 x 20.6 x 41.2 mm / 1.6 x 0.81 x 1.62 in
Weight (gram)	83.0 ± 1 grams / 2.93 oz

Includes Servo and Aluminum Servo Arm

MKS-X8 Metal 3" Rudder Arm

X8 3" and 2.5" Rudder Metal horn.

This horn will only work on our X8 8mm Spline.
HBL380, HBL850, HBL880 and HBL860

MKS-2015-11

$23.50 23.50

Bob Smith Industries 304 Pocket CA Extender Tips for Pocket CA Tops (6 Pack)

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.